MaltMuncher 3 Roller Grain Mill | Cold Rolled Steel Rollers | Adjustable Gap Setting | 12 lb Hopper Capacity

MaltMuncher 3 Roller Grain Mill | Cold Rolled Steel Rollers | Adjustable Gap Setting | 12 lb Hopper Capacity

In Stock
Delivers to ( change ) by as part of our Fast & Free Shipping.
Faster Shipping Available. Details.
60 day no hassle return policy. Details

  • Mill your own grains on brew day for increased freshness and higher efficiency!
  • Adjustable gap setting allows you to fine tune your preferred crush level and adapt to the kernel size of different malts
  • 12 TPI knurl to efficiently pull grain through rollers while leaving hull intact to form an excellent filter bed for sparging
  • 3 roller mills are more effective at cracking the husk of the grain and offer better crushing performance in a single pass
  • Included crank handle can be detached to power the driven roller with an electric drill or motor

Mill your own grains for ultimate freshness with the MaltMuncher three roller grain mill.  Includes a 12 lb hopper, adjustable rollers, and hand crank. The handle can be removed to use the mill with a drill. The MaltMuncher is backed by a one year warranty and is built to last with rollers made from cold rolled steel.  The body and hopper is made from 6061 grade aluminum. The optional PPE base board is much stronger than comparable particle board or plywood bases and makes for a secure platform to set on a bucket.

Do you love to make your own equipment?  Make an amazing motorized mill with the optional MaltMuncher high torque motor  designed to work with the Maltmuncher 3 roller grain mills.  


  • Comes with 12 lb hopper and crank handle
  • Great for use with a power drill
  • Cold rolled steel rollers sized at 5" long by 1.25" diameter
  • Adjustable rollers at both ends to move the gap from 0" - 0.063"
  • If motorized we recommend 200 rpm
  • 12 TPI knurl to effectively pull grain through the rollers while still leaving the hulls intact to later form an excellent filter during the sparge
  • 12 mm crank shaft

Kegland Part Number: KL03261

Please note: This mill is designed for use with brewing grains only. It will not work for cracking whole kernel corn.

Item # MILL710
Shipping Eligible for Free Shipping Program
Availability California - In Stock
Pennsylvania - In Stock
Weight 12 LBS
Community Q&A

Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 10 questions Browse 10 questions and 21 answers
Why did you choose this?
MoreFlavor Store
Looked best for my needs, best price found
Hugh m on Feb 14, 2023
Want to start milling my own grains.
Mark on Oct 5, 2022
Looked best for my needs, best price found
Hugh m on Feb 14, 2023
Great ratings
Ronald I on Dec 12, 2022
Want to start milling my own grains.
Mark on Oct 5, 2022
Because I didn't want to buy this after buying a 2 Roller Grain mill
David W on Sep 7, 2022
LHBS closing down. Need to take drastic measures
Brendin J on Aug 5, 2022
Homebrew 4 life, an excellent youtuber recommended this mill. I have never done ANY brewing at all and this will be the braj way ...MBC MBC MBC.
Patrick T on May 18, 2022
replace my older mill
jim on Apr 20, 2022
Good reviews and price
Sidney D on Apr 7, 2022
I own one, and have used reliably for years, but it is time to replace
Neil C on Mar 16, 2022
Good reviews and I need a new one.
Ray B on Mar 4, 2022
3 roller is best
Valued C on Mar 2, 2022
Upgrade from my 10 yr old Barley Crusher
Justin W Thomas on Feb 25, 2022
Upgrade to a better grain mill.
James M L on Jan 22, 2022
Son is doing micro brewing
susan a on Dec 7, 2021
I wanted to upgrade from a 2 roller mill to a 3 roller.
Kraig P on Nov 23, 2021
upgrade grain mill size
Tim P on Nov 18, 2021
Great "Deal of the Day" I will be able to grind grains when I need them and to my satisfaction.
William Brennan on Sep 17, 2021
Recommended based on reviews
Bill W on Sep 15, 2021
Good review of product on another site, prefer 3 roller system, best price here
524 Union S on Jul 14, 2021
Price and reviews
Kenny Cason on Jul 14, 2021
My homebrew shops’ mill is not adjustable and I want more efficiency for my BIAB set up
John F on Jun 29, 2021
For best grind yield...
Carmen De N on Jun 7, 2021
Want to start self milling for ultimate freshness
Walter M on Apr 3, 2021
Mathew C on Mar 16, 2021
Better control
Merlin J Foard on Mar 12, 2021
It was the best price for the item. Didn't have any promo codes at the time but what can ya do?
Neil F on Feb 15, 2021
To match the motor
Christopher I on Jan 21, 2021
I will be starting to mill my own grain, instead of relying on the brew shop to grain
Patrick W on Jan 15, 2021
Quality and consistency of grind
Michael E on Jan 15, 2021
Ordered for a Christmas Present for our son's home brewery.
Diane K on Jan 14, 2021
Bought this for my husband for Christmas
Anjelica M on Dec 2, 2020
3 roller action baby!!!
stephen h on Dec 1, 2020
sold my old one when we moved
David P on Dec 1, 2020
Upgrade from a tabletop mill.
Randall C on Nov 30, 2020
Requested by recipient
Terry C on Nov 30, 2020
Good Reviews
Idalmis Reyes on Nov 28, 2020
3rd roller for more consistent milling
Dave on Nov 28, 2020
Amazing Black Friday deal!!!
John Greene on Nov 28, 2020
high review marks, construction and operation details, overall look
Tim U on Nov 26, 2020
Mrs. Rita T on Nov 26, 2020
need one and chose this
prof p on Nov 18, 2020
I wanted a grain mill and have read the 3 roller ones are better. This one was recommended.
Nickolas S on Nov 5, 2020
For quality malt sparging
Aaron on Oct 27, 2020
It had the best reviews for the price, and seems like a machine that will last for many years!
Federico B on Oct 24, 2020
recommendation from a friend
Bruce K on Oct 20, 2020
I want to start milling my own grains.
Micky B. on Sep 26, 2020
Recommended by Brew club
Matthew S C on Sep 14, 2020
brian w on Aug 27, 2020
Tired of inconsistent LHBS crushes
Gregory S on Aug 26, 2020
3 rollers is better than 2
David F on Aug 25, 2020
Great ratings
Ronald I on Dec 12, 2022
Because I didn't want to buy this after buying a 2 Roller Grain mill
David W on Sep 7, 2022
Can anyone confirm if this model has ball bearings or if it has bronze bushings?
Joel Donmeyer on Dec 26, 2019
BEST ANSWER: looks like ball bearings
Does anyone have directions on setting the roller gaps?
42X on Jan 5, 2020
BEST ANSWER: I use the .036” setting, which is slightly smaller than 1mm. This setting gives me a nice grain crush with overall good efficiency and no problems with a stuck sparge at this setting.
Can grain be finely crushed with this mill, like flour?
Stefan Mueller on Jan 8, 2021
BEST ANSWER: No. BUt you can get a nice fine crush, about.025", or credit card width, .030. Perfect for my use. What a great mill, never will I go back to a two roller mill.
What are the vertical dimensions with the hopper attached?
Aaron Nicodemi on Mar 29, 2020
BEST ANSWER: Mounted to a 1/2 inch base, vertical height is 13 1/2” with the standard hopper and 23” with the extended hopper.
What size drill is needed?
Lenny N on Jan 14, 2020
BEST ANSWER: 1/2 " chuck - variable or low speed is recommended. Anchor down this mill very well when motorizing - the 1/2" drill has a lot of torque and could rotate the whole mill (rather than the rollers). Before motorizing, hand crank it empty to make sure the rollers are aligned then add a few oz. of grain to check it again. Then use the drill.
Will this grind corn?
Van M Randall on Mar 22, 2022
BEST ANSWER: No, it’s not recommended for corn.
What size bolts are required to mount the mill to the base?
Gerald Kroupa on Feb 25, 2021
BEST ANSWER: My unit is about 18 months old and assuming they haven't changed, they are metric M6 x 1.0 bolts. The 1.0 is the pitch not the length. The length will depend on how thick of a board you use. The threads are about 3/4 inch deep into the mill. My bolts were 30mm with a 1/2 inch board and I had to use a large nut as a spacer to keep the bolt from bottoming out before it was tight, but it was what I already had at available. Drilling the 4 holes in the exact place is made easier if you do a rubbing on the mill and use it as a template to drill the holes. Good luck.
Could someone be kind enough to check the roller dimensions on this mill? (I have seen both 5" x 1.25" and 6" x 1.5") Thanks
Mike Goetzke on Jan 20, 2021
BEST ANSWER: The rollers are 1.375" x 6" long. The thread count for the bolts are not widely available and I have not been able to locate bolts to fasten the rig to a base. I would not buy this again.
I currently have the motorized MaltMuncher 2-roller model, powered by a motor (item #MILL705). If I ever want to swap out the 2-roller mill for this 3-roller version, is it a direct replacement? Specifically, is the axle/shaft of the 3-roller version at the same height and extends the same length away from the body as the 2-roller?
Daniel Cook on Oct 29, 2019
BEST ANSWER: Daniel - I would guess the driver roller is the same height, but wouldn't be offset like the two roller.
What is the height of the driveshaft from the base to the center of the driveshaft (in mm)?
Don Tupper on Mar 22, 2023
BEST ANSWER: Approximately 66 mm

4.4 / 5.0
56 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Rated 5 out of 5
Great item
This was a gift to my son, he's into making beer and other grain drinks.
January 26, 2023
1 year ago
Rated 2 out of 5
Need directions added to the shippmen6
Have only used it twice and it seems to do a good job. The reasoning behind my low rating is there were no directions in the kit, had search through you tube videos until I found one that started from the beginning on the assembly. My second point of distinction there are directions how to set the gap, could not find anything definitive on the internet. I muddled through it but not sure if the gap is set correctly.
November 30, 2022
1 year ago
Rated 5 out of 5
Well built grinder.
Easy to use with a cordless drill. Grinds smoothly. Can be adjusted for more or less coarse depending on grain needs.
August 20, 2022
over 2 years ago
Rated 5 out of 5
Malt Munch 3 Roller Grain Mill
Replacing two roller mill that’s 10 yrs old. This has three rollers. Looks very sturdy and had great reviews, so I purchased it. Can’t wait to try!
May 3, 2022
over 2 years ago
Rated 3 out of 5
Good but needs work.
I put it together but haven't used it yet. I don't like how it does not come with instructions.... i had to be figuring it out like a puzzle for a good hr.... I had to make the board to stand it on a bucket wich is not bad but i had to guess what size bolts to add underneath because the mill does not come with them. 5 stars on the function, 3 stars on the setup.
April 30, 2022
over 2 years ago
Rated 4 out of 5
Nice mill!
Easy to put together, just look up a Youtube video if you can't figure it out on your own. Easy to use and adjust the gap once you know the trick (you turn the adjustment bolts opposite from each other, watch the video if you can't figure it out). The main problem I had with it was that if you tighten the eye bolts too tight, it will prevent the third roller from rolling and the mill won't work, I spent about 45 mins trying to figure that one out, so I took off a star.
March 24, 2022
over 2 years ago
Rated 5 out of 5
Good 3 roller for the money.
I've only used it once, but pretty impressed with this mill on that brew day. This replaces my 10 year old Barley Crusher. About the only negatives are lack of instructions and it's made in China. Pretty easy to figure out by using some of the videos on YouTube as a guide.
March 10, 2022
over 2 years ago
Rated 4 out of 5
setup fail
Well first off this thing works great if you can get it put together with zero instructions and no instructions on how to adjust the thing. Also do not wait until your brew day to put it together. I had to run to the hardware store since it did not have the hardware to mount this to the surface that is sold separately. The small rubber gasket falls off very easily.
December 20, 2021
over 2 years ago
Rated 5 out of 5
works great easy to adjust
only complaint is there is no assembly instructions
August 4, 2021
over 3 years ago
Rated 5 out of 5
Game changer
I purchased this mill after years of frustration with my BC mill. The BC served me well for 10+ years, but the rollers wore down and it would anger me more than anything else. Enter this mill. Two words: Game Changer. This mill rips through grain. Assembly was easy despite the lack of instructions; most of it was common sense. Setting the mill gap took a bit to figure out, but once I realized how the cams move the adjustable roller it made sense. The .032 setting made for a perfect crush for my eBIAB rig. I would highly recommend this mill to anyone from novice to expert.
July 27, 2021
over 3 years ago